Classic slime needs just PVA glue and an activator that contains borate. Mix them and the glue turns from a liquid into a stretchy, pokeable slime in about two minutes. Below is the easiest version, using contact lens solution, and the classic borax version.
Easy contact lens solution slime
Makes: about ½ cup · Time: 5 minutes · Difficulty: easy
Ingredients
- ½ cup (120 ml) white PVA school glue (for example Elmer’s)
- ¼ cup (60 ml) water, optional, for a stretchier slime
- ½ teaspoon baking soda
- 1 tablespoon contact lens solution that lists boric acid and sodium borate in the ingredients, plus a little extra
- Food colouring or glitter, optional
Method
- Pour the glue into a bowl. Stir in the water, if using, until smooth.
- Add colouring or glitter now and mix well.
- Stir in the baking soda until fully dissolved.
- Add 1 tablespoon of contact lens solution and stir. The mixture will thicken quickly and start pulling away from the sides of the bowl.
- When it forms a blob, pick it up and knead for 1 to 2 minutes. It will be sticky at first and get smoother as you knead.
- If it is still sticky after kneading, add ½ teaspoon more contact solution and knead again. Repeat only if needed.
Want a bigger or smaller batch? The slime recipe calculator scales every recipe on this site.
Classic borax slime
Ingredients
- ½ cup (120 ml) white PVA glue
- ½ cup (120 ml) water
- Activator: 1 teaspoon borax powder dissolved in 1 cup (240 ml) warm water
Method
- An adult should make the activator: stir the borax into the warm water until completely dissolved. Let it cool.
- Mix the glue and ½ cup water in a bowl.
- Add the activator 1 tablespoon at a time, stirring well after each addition. Usually 2 to 4 tablespoons are enough.
- Stop when the slime holds together and pulls away from the bowl, then knead until smooth.
Keep the leftover activator in a labelled, closed jar out of reach of children.
Why it works
PVA glue is a solution of long polyvinyl alcohol (or polyvinyl acetate) molecules. Borate ions in the activator form temporary bridges between those long chains, called cross-links. The glue turns from something that flows into a loose network that stretches, but can also be pulled apart, and slowly flows again if you leave it. That is why slime behaves partly like a liquid and partly like a solid.
Baking soda raises the pH slightly, which helps the borate in contact lens solution do its job, so a small amount of solution goes a long way.
Is slime safe?
- Borax powder should only be handled by adults. Never let the dry powder touch skin directly and keep it away from eyes and mouth. There have been reports of skin irritation and burns from handling too much activator or using undiluted borax, so stick to the small amounts above.
- “Borax-free” is not “boron-free”. Contact lens solution and liquid starch also use borates, just at lower concentration. They are gentler, not completely different. For truly borate-free options see slime without glue and slime without borax.
- Sensitive skin: if hands become red or itchy, stop and wash them. Gloves are fine for making slime.
- Clean up: slime comes out of fabric with white vinegar and warm water. Avoid hot water, which can set glue.
Troubleshooting
| Problem | Fix |
|---|---|
| Too sticky | Knead for longer first. Then add activator in very small amounts. |
| Too stiff or rubbery, snaps instead of stretching | Too much activator. Knead in a little warm water or a pump of hand lotion. |
| Never comes together | Check the contact solution contains boric acid and sodium borate, and the glue is PVA. Some “washable” glues need more activator. |
| Dried out after a few days | Store in an airtight container. See how to fix slime for revival tips. |
Next recipes to try
- Fluffy slime with shaving foam
- Slime without borax: three gentler activators
- Homemade kinetic sand
- Or just watch: slime ASMR videos